question

[Igor Gueths]

Hi Victor. I have network access. There are two things that I don't have as of yet. 1 of them is Dns, and the other is I don't have it set to configure the interfaces with pump on start-up. Does anyone know how I could go about doing this? Thanks!
----- Original Message ----- 
From: Victor Tsaran <tsar at sylaba.poznan.pl>
To: <speakup at braille.uwo.ca>
Sent: Monday, March 18, 2002 9:15 PM
Subject: Re: question 


> Hi, Igor!
> Loopback interface will work regardless of whether your physical network
> card working or not. Loopback interface, 127.0.0.1, is present in Linux by
> default. So your card is not working properly if it is not detected by
> ifconfig.
> Vic
> 
> ----- Original Message -----
> From: "Igor Gueths" <igueths at yahoo.com>
> To: <speakup at braille.uwo.ca>
> Sent: Tuesday, March 19, 2002 12:24 AM
> Subject: Re: question
> 
> 
> > Hi Victer. The card is actually recognized, and the
> > module seems to load fine. In fact, when I do
> > ifconfig, I get status messages. Something like this:
> > Loopback=127.0.0.1. Netmask=255.255.0.0. Mtu=16300.
> > Then it goes on to display packet stats. At least I
> > got an mtu reading that wasn't 0, so I believe that
> > this could indicate that the interface is functioning.
> > Is this so? By the way, to answer your question on the
> > SMC cards, I actually have a Linksys card that uses
> > the tulip module.
> > What I'm planning to do something like ifconfig eth0
> > -dhcp to configure the interface based on dhcp. Also,
> > sorry for the long response time, its just that mail
> > over here was down for about two days, and its back
> > up. -I have also noticed an interesting atribute in
> > kernel 2.4.18. Every time -I press the del key,
> > dec-talk says numlock on. COuld this have to do with
> > an incorrect keymap being loaded at boot time? Thanks
> > in advance!- Victor Tsaran <tsar at sylaba.poznan.pl>
> > wrote:
> > > Hi, Igor!
> > > Is there a possibility that your netcard module
> > > conflicts with another
> > > module which kicks it out? Can you do a full "dmesg"
> > > trace and see what
> > > happens there? Also, if I remember correctly,
> > > tulip.o module was for SMC
> > > cards, right? If yes, then I think there was some
> > > update to that module last
> > > year. But that might not apply to you since you are
> > > using the newest kernel,
> > > is that so?
> > > Also, I think that your card might be recognized by
> > > the hardware detection
> > > tool, but the module itself does not load. Perhaps
> > > you should check your
> > > /etc/modules.conf or edit your /etc/rc.d/rc.local to
> > > have your module load
> > > at startup.
> > > Vic
> > >
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Speakup mailing list
> > > Speakup at braille.uwo.ca
> > >
> > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Yahoo! Sports - live college hoops coverage
> > http://sports.yahoo.com/
> >
> > _______________________________________________
> > Speakup mailing list
> > Speakup at braille.uwo.ca
> > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
> >
> >
> 
> 
> 
> 
> 
> _______________________________________________
> Speakup mailing list
> Speakup at braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup


_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com