cdrecord question

[Gregory Nowak]

Hi Igor,

Act on my previous post, then try cdrecord again. If it still doesn't work after you've rebuilt your kernel/modules in regards to my previous post, let me know what you get, and we can go from there. I'm running slackware 8.0. If this is your set up, then ...
Greg


On Sun, May 05, 2002 at 08:37:16PM -0400, Igor Gueths wrote:
> Hi Greg. Unfortunately, I tried it with -dev=/dev/sr0, and got the
> following:
> scsidev: /dev/sr0
> scsibus: 2 target: 2 lung: 2
> cdrecord: bad file descriptor. Could not open scsi driver
> cdrecord: For possible targets try cdrecord -scanbus. Make sure you
> are root
> 
> 	And when I do cdrecord -scanbus, it says: "No such file or
> directory, cannot open scsi driver. Is this normal since the drive isn't
> an actual scsi drive, rather it is being emulated as such? Also, I thought
> I remembered seeing an environment variable or two which cdrecord used to
> determine the correct /dev for the Cd recorder? Is it normal for you to do
> cdrecord -scanbus and to get the error I described above since you are
> running pretty much the same setup as me as far as I know? Thanks!
>  On Sun, 5 May 2002, Gregory Nowak wrote:
> 
> > Actually, your drive is and should be ide-scsi emulated. For me, my burner is at /dev/sr0.
> > Greg
> >
> >
> > On Sun, May 05, 2002 at 06:05:25PM -0400, Igor Gueths wrote:
> > > Hi. I am using an atapi drive. Also, I have passed append="hdd=ide-scsi"
> > > to /etc/lilo.conf. After rebooting the system, the scsi emulation driver
> > > maps the burner to scsi0. Doesn't that mean that /dev/scd0 should be the
> > > Cd burner, since my Cdrom drive isn't using scsi emulation?
> > >
> > > On Sun, 5 May 2002, 'Georgina' wrote:
> > >
> > > > Hi
> > > >
> > > > I think that you've neglected to send the whole message.  What's your
> > > > question?  If its a IDE burner, are you using the generic scsi module?
> > > > Have you specified hdd-scsi?  Have you examined your boot messages to
> > > > see how the system is seeing your burner?
> > > >
> > > > Gena
> > > >
> > > >
> > > >
> > > > Blindness Advocacy and Self Help Online www.bashonline.org
> > > >
> > > > >Hi all. I also tried dev=/dev/scd0, dev=/dev/sg0, and dev=/dev/hdd. When I
> > > > >tried dev=/dev/hdd, I got an I/O error: Cannot open scsi driver. When I
> > > > >tried sg0 and scd0, I got cdrecord: Bad file descriptor. Could not open
> > > > >scsi driver. Any ideas on how to fix this? Thanks again!
> > > > >
> > > > >
> > > > >_______________________________________________
> > > > >Speakup mailing list
> > > > >Speakup at braille.uwo.ca
> > > > >http://speech.braille.uwo.ca/mailman/listinfo/speakup
> > > >
> > > > _______________________________________________
> > > > Speakup mailing list
> > > > Speakup at braille.uwo.ca
> > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> > > >
> > >
> > >
> > > _______________________________________________
> > > Speakup mailing list
> > > Speakup at braille.uwo.ca
> > > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
> > _______________________________________________
> > Speakup mailing list
> > Speakup at braille.uwo.ca
> > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
> 
> 
> _______________________________________________
> Speakup mailing list
> Speakup at braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup