Hardware Question

[Alex Snow]

Yup, I'll get the model
----- Original Message -----
From: "Pete" <persuric at ameritech.net>
To: <speakup at braille.uwo.ca>
Sent: Sunday, March 10, 2002 2:50 AM
Subject: Re: Hardware Question


>
>   You will want to go to the maxtor site and get a tech/spech sheet on
your
> drive.  I have a couple of old maxtor drives and I know what you mean
about
> the jumpers not being labeled as ma/sl/cs.  On the spec/tech sheet it will
> tell how to set the jumpers on the primary HD so it can work whith a slave
> drive conected to the same ribbon.  Just a passing thought, did you check
to
> see in bios whether or not the primary slave drive selection was enabled
or
> set to auto or not?  Some C D rom drives have a proprietary interface that
> connects to a sound card only.  It may or may not have a 40 pin conecter
but
> it may or may not be IDE. Usually these c d roms came bundled whith a
sound
> card.  This may be what kind of c d rom you have.  Can you get the model
> number off of it?
>   Pete
>
> ----- Original Message -----
> From: "Alex Snow" <alex_snow at gmx.net>
> To: <speakup at braille.uwo.ca>
> Sent: Saturday, March 09, 2002 10:15 AM
> Subject: Re: Hardware Question
>
>
> Hi Ed.
> I'm usually good with hardware, but this is anoying.  The cdrom is a
Mitsumi
> 4x dated 1995.  The hard drive is a Maxtor 240 mb drive dated 1993.  The
> cdrom has jumper pins on the back labeled cable sellect, slave and master.
> I pulled the actual thing that you move on the jumpers of an old 1x.  I
set
> the jumpers at slave on the cdrom and am leaving the hd alone since it
> doesn't have labeled jumpers.
> ----- Original Message -----
> From: "Ed Barnes" <ed.barnes at janus.northatlantic.nf.ca>
> To: <speakup at braille.uwo.ca>
> Sent: Friday, March 08, 2002 10:45 PM
> Subject: Re: Hardware Question
>
>
> > Hi Alex.
> > Just curious if you know the manufacturer of this cd-rom and its model
> > number and if you could send it along.
> > This may help in one of us or yourself consulting the manufacturers
> > regarding the drive's default behaviour as it seems that it is
jumperless.
> > Also, how old approximately is it, and what speed is it, as you probably
> > know, there are less and less certainties with regard to cd-roms when
you
> > get into 1x, 2x, and 4x teritory or even a bit later.
> > I would second Kerry's suggestion regarding that it probably defaults to
> > either slave or cable select if it is without jumpers.
> > I feel however that if we had more info on the drive, I.E., model and
> > manufacturer as mentioned above that this would help us a great deal.
> > I should close with a bit of a disclaimer of sorts, despite the fact I
> have
> > loads of hardware experience in respect to DOS and Windows environments
I
> > am a linux newbie in the wirse way though I am chomping at the bit.
> > Regards,
> > Ed Barnes
> >
> >
> > At 06:10 PM 08/03/2002, you wrote:
> > >Hi.
> > >Thanks for the quick response!
> > >Yup.  Thats the way the cdrom looks.  Only problemis, The three sets of
> > >jumpers don't have any of those jumper things on them.  They just are
> three
> > >sets of 2 pins.
> > >Found it on the hd thou.
> > >----- Original Message -----
> > >From: "Kerry Hoath" <kerry at gotss.net>
> > >To: <speakup at braille.uwo.ca>
> > >Sent: Thursday, March 07, 2002 8:34 PM
> > >Subject: Re: Hardware Question
> > >
> > >
> > > > I've posted on this before but here we go again:
> > > > With the connectors of the cdrom towards you you have:
> > > > power on the right, 4-pin.
> > > > IDE ribbon connector 40-pin
> > > > then a jumper block then redbook audio then digital out and mode
> jumpers
> > >working your way to the left.
> > > > The jumper pins closed to the 40-pin ribbon cable is master,
> > > > the next set are slave and the next set are cable select.
> > > > If there is a secondary ide controller put the cdrom on that since
> > > > some hard drives have different jumperings for single drive
> > > > and drive with slave especially western digital.
> > > > Otherwise cdrom as slave is on the center of the set of 3 jumpers
next
> to
> > >the ribbon.
> > > >
> > > > Regards, Kerry.
> > > > On Thu, Mar 07, 2002 at 06:57:07PM -0500, Alex Snow wrote:
> > > > > Hi.
> > > > > I am installing a temperary verson of linux on an old 486 box.  To
> Get
> > >linux from the winblows machine to the 486, I need to install a CDrom.
I
> > >hooked it to the same ribbon as the hd since there was room, but it
won't
> > >boot with the cdrom on the controler.  How do I tell the hd to be
master
> and
> > >cdrom to be slave?
> > > > --
> > > > Kerry Hoath:  kerry at gotss.net kerry at gotss.eu.org or
> > >kerry at gotss.spice.net.au
> > > > ICQ: 8226547 msn: kerry at gotss.net Yahoo: kerryhoath at yahoo.com.au
> > > >
> > > > _______________________________________________
> > > > Speakup mailing list
> > > > Speakup at braille.uwo.ca
> > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> > > >
> > >
> > >
> > >_______________________________________________
> > >Speakup mailing list
> > >Speakup at braille.uwo.ca
> > >http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
> >
> >
> > _______________________________________________
> > Speakup mailing list
> > Speakup at braille.uwo.ca
> > http://speech.braille.uwo.ca/mailman/listinfo/speakup
> >
>
>
> _______________________________________________
> Speakup mailing list
> Speakup at braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>
>
> _______________________________________________
> Speakup mailing list
> Speakup at braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>